What Happens to a CPU When the Fan Dies?

A CPU’s operating temperature will rise if the cooling fan breaks, dramatically increasing the chance of hardware failure. Stock modern computer CPUs use a two-part CPU cooler that features a heatsink directly connected to the CPU and a fan that cools the heatsink. The fan’s role is secondary, but it is of vital importance in preventing the CPU from overheating: the heatsink will not dissipate heat fast enough to prevent damage to the CPU without an operational fan.

Overheat

CPUs with dead fans will overheat. Computers usually have built-in safe guards to shut down or slow down the CPU when it gets too hot to prevent it from breaking. However, if the computer’s safeguards fail or do not kick in fast enough the CPU can get above its maximum operating temperature and literally burn out. The CPU can get so hot it will ignite, destroying itself beyond repair. A fried CPU can also take down the motherboard and other connected components with it when it goes. The CPU will break if the computer is continually used with a dead ACER 3BZF1TATN04 CPU Fan.

.

When the Fan Dies

If the CPU fan fails, shut down the computer immediately to prevent hardware damage Running a normal system shut down may not be fast enough:. In this instance it can be safer to shut down via holding the power button or pulling the plug Hard shutdowns. run the risk of damaging data, but leaving the system on even just a little longer to shut down via normal methods runs a high risk of destroying the computer.

Intel and AMD Defense Mechanisms

Intel and AMD CPUs will produce error messages and try to shut down if the ACER 3BZF1TATN04 CPU Fan. fails. Intel CPUs will drop the CPU’s clock speed to prevent it from going above its operating temperature range. These CPU defense mechanisms are designed to prevent the computer from breaking in the event of CPU cooling failure. If you turn the computer back on, it will display an error message and cut power in a few seconds to prevent CPU damage. Repeatedly trying to power on the system again can damage the CPU as the CPU can get above its maximum operating temperature in seconds without sufficient cooling.

Replace

A dead ACER 3BZF1TATN04 CPU Fan. should be replaced immediately after failure and the computer should not be used again until a functional cooling unit is installed. It’s typical to replace the entire cooling unit when the fan fails. Additionally, the thermal cooling compound that bridges the physical connection between the heat sink and the CPU needs to be replaced when installing a new cooling unit You can install the new unit yourself or bring it to a professional:. incorrect cooling unit installation can also break the CPU A CPU that’s powered on without cooling. or poorly installed cooling can ignite in seconds.

ACER 3BZF1TATN04 CPU Fan

How to install a new CPU cooler – step by step

Choosing the right model and installing it properly

If your laptop quite literally never fails to make itself heard, you might want to take a look at the usual suspect for persistent fan noise:. Your CPU cooler Here’s a detailed, visual guide on how to replace it with something better and what to keep in mind.

 Be it turbo mode, hyper-threading or even multiple cores -. Modern CPUs have come a long way since the inception of very first microprocessor And though ever smaller manufacturing methods have greatly helped to keep temperature emissions in check, the corresponding development of “boxed “CPU coolers has been somewhat less spectacular. Even today, neither Intel nor AMD bother to equip their processors with anything more than what is absolutely required, leading to unnecessarily high temperatures and relentless fan noises, slowly chipping away at the sanity of laptop users in those midsummer days.

 It is probably common knowledge that the most effective and permanent solution to this torment is to upgrade to a bigger and more sophisticated ACER 23.AT902.001 CPU Fan . Somewhat less obvious, however, are the exact steps on how to do so. Here’s what you need to keep in . mind and how to make the operation go smoothly See also: How to upgrade a PCs processor

Choosing the right CPU cooler

In order to find a compatible model, you will first have to find out what kind of socket your CPU uses. This can be easily accomplished by downloading and installing the nifty hardware utility CPU-Z. Fire it up and look for the field “Package “under the tab” CPU “This will give you the exact specification of your mainboard socket -. for example” Socket 775 LGA “Note it down and make sure that your future cooler supports this particular format (more expensive coolers are often compatible with. multiple different sockets).

The coolers themselves can come in many different shapes and forms, typically starting as low as £ 5 and going all the way up to £ 70 depending on the quality, manufacturer and popularity. Which one you should choose differs from socket to socket and is ultimately up to you. It’s almost a given however, that anything beyond £ 15 will easily upgrade your stock cooler. Obviously, we recommend reading some reviews to find out which one works best for your specific system and budget.

 Additionally, size matters -. At least in terms of cooling While professional fan models can easily be twice the size as their boxed counterparts and might seem excessive at first, they are much more efficient at dissipating heat away from the processor due to their greater amount of metal surface -. also called “heatsink” Thus, if you are planning on buying a rather “prominent” cooler, you might want to compare its measurements (particularly the height) with the actual space of your laptop case to make sure it fits inside.

Note: Though the boxing of most coolers typically includes a small amount of thermal paste, its quality can diverge wildly, thus potentially mitigating the cooling performance If you want to go the extra mile and make the most out of your new cooler, see if. you can you can get your hands on some high-quality ceramic or silver-based thermal compound (particularly fancy mixtures might even include diamond dust).

Also take a look at: Overclock your CPU, GPU and RAM

How to replace your ACER 23.AT902.001 CPU Fan

To get started, shut your system down and flick the switch on the back of your power supply to “Off” (which can itself be accessed from back of your PC). As this is going to be a fairly elaborate endeavour, it’s a good idea to remove all cables from your computer and lay it down an an flat and well lit surface for easy access.

Also, make sure to ground yourself on a metal object before proceeding (such as your radiator), and try to steer clear from carpets (and other objects that might charge you up again) for the time being.

1. Open your case from the side to get a good look at the insides of your PC. Many coolers require the installation of a backplate on the other side of your motherboard to stabilize them. If this applies to your model, you will likely have to remove the motherboard itself to reach the right spot – start by removing potential screws that might hold your graphics card in place If not, jump to step 7..

2. While older models can be pulled out from their PCI slot without any further mechanisms, most modern graphics cards require you to pull a small plastic level on its side. Some may even be connected to your power supply directly with one or two 6- pin connectors. Unplug them and remove the card.

3. Next, look for the screws that are keeping your motherboard attached to the laptop case. Simply, check the borders to find the lot of them (the last one is normally located just below your CPU in the middle). Try to loosen them all at roughly the same rate until they can be removed.

4. Unplug all cables connected to your motherboard that are interfering with the removal. If you are not sure whether or not you can reconnect them properly later on, its a good idea to make a photo while everything is still in place. Marked in our photo: The 24-pin and 4-pin power supply connectors and the SATA slots.

5. Typically, there are nine screws to be removed from ATX motherboards, though this may vary with other form factors. Make sure you got them all and put them someplace safe for the time being.

6. Carefully lift your motherboard out of the case. It’s up to you whether or not you want to remove all cables from the motherboard, as this might overcomplicate the re-installation for dexterous tinkerers. For maximum comfort, it’s obviously better to do so and to take the motherboard someplace else.

7. A close up of our old ACER 23.AT902.001 CPU Fan -. Already a bit dusty Notice the small size of the fan blades.

8. Look for the small 4-pin cable that extends from the cooler to the motherboard. Gently waggle it off without bending the pins.

9. Next, you will have to remove the cooler itself. See if there’s a small lever at the side to push down. Depending on your respective model, the exact method of removal might differ. If there’s no lever to be found, you can typically find four push-pins at each corner.

10. After pressing down the lever, release the metal clamp from both sides of the cooler. If you are dealing with push-pins instead, try turning your motherboard around and see if your can squeeze the two halfes of each pin together in order to loosen it.

11. On the left: Our new “Scythe Mugen II” (about £ 35); on the right: The old boxed cooler.

12. As you will have noticed, your CPU is now finally brought to light. The greasy paste on top of it is a thermal compound that improves the heat conductivity between the CPU and the cooler, thus improving the cooling performance (air alone would be significantly less effective). Refrain from touching it and ignore it for now.

13. If your new cooler requires you the install a backplate onto your motherboard, turn it around and do so.

14. Additionally, take a look into the manufacturer’s manual and see if there are instructions as to how the cooler needs to be modified before being placed onto your respective socket. This typically includes assembling the mounting device in a particular fashion.

15. Attach the fan to the heatsink. This is often accomplished with the help of metal brackets.

16. Time to get back to the CPU. It is highly advisable to remove the rest of the old paste before applying a new dose. Carefully wipe the bulk of it away with a clean piece of cloth.

17. Next, take another piece of cloth and slightly moisten it with pure or rubbing alcohol (at least 70% +). Gently sweep the surface of the CPU with it a couple of times to remove all residues. Take care not to accidentally touch the surface, as this will likely leave greasy fingerprints.

18. Apply a tiny dose of fresh thermal paste – a bit smaller than the size of a pea -. On top of your CPU and evenly spread it with the help aa strong sheet of paper (business cards will do) The idea is to thoroughly cover the whole surface while keeping the layer as thin as possible to ensure ideal cooling conditions.

19. If present, make sure to remove the plastic foliage covering the underside of your ACER 23.AT902.001 CPU Fan. Again, try not to accidentally touch the metal surface with your fingers after doing so.

20. Put all necessary backplate screws in place and rotate the cooler until it matches their position. Gently lower it onto the CPU, ideally without twisting it around too much once it is has made contact. Tighten the screws connecting the cooler to the backplate / motherboard.

21. Once the cooler is firmly connected to the motherboard, make sure it pushes the air out of the rear of your laptop case to optimize airflow (whether you place the fan before or behind the heatsink is up to your model and preference).

22. As a final step, put your motherboard back into the PC case and reattach all necessary screws as well as the cables and PCI cards that you previously removed. Do not forget to connect the fan power plug to the 4-pin connector on the motherboard before closing it up again.

ACER 23.AT902.001 CPU Fan

Battery Knowledge Tips & FAQ

Batteries Care Instructions

Battery Do’s:

A new ACER 4ICR17/65 Replacement Battery  comes in a discharged condition and must be charged before use (refer to the devices manual for charging instructions). Upon initial use (or after a prolonged storage period) the battery may require three to four charge / discharge cycles before achieving maximum capacity.

When charging the battery for the first time the device may indicate that charging is complete after just 10 or 15 minutes. This is a normal phenomenon with rechargeable batteries. Remove the battery from the device, reinsert it and repeat the charging procedure.

It is important to condition (fully discharge and then fully charge) the battery every two to three weeks. Failure to do so may significantly shorten the battery’s life (this does not apply to Li-Ion batteries, which do not require conditioning). To discharge, simply run the device under the battery’s power until it shuts down or until you get a low battery warning. Then recharge the battery as instructed in the user’s manual.

If the battery will not be in use for a month or longer, it is recommended that it be removed from the device and stored in a cool, dry, clean place.

It is normal for a battery to become warm to the touch during charging and discharging.

A charged battery will eventually lose its charge if unused. It may therefore be necessary to recharge the battery after a storage period.

The milliamp-hour (mAH) rating of the Hi-Capacity battery will often be higher than the one on the original battery. A higher mAH rating is indicative of a longer lasting (higher capacity) battery and will not cause any incompatibilities. A Hi -Capacity battery will, in most cases, outperform the original by 30% to 50%.

Actual battery run-time depends upon the power demands made by the equipment. In the case of notebook computers, screen brightness, the use of the CPU, the hard drive, and other peripherals results in an additional drain upon the battery, effectively reducing the battery’s run-time. The total run-time of the battery is also heavily dependent upon the design of the equipment. To ensure maximum performance of the battery, optimize the computer’s power management features. Refer to the computer manual for further instructions.

Battery Don’ts:

Do not short-circuit. A short-circuit may cause severe damage to the battery.

Do not drop, hit or otherwise abuse the ACER 4ICR17/65 Replacement Battery as this may result in the exposure of the cell contents, which are corrosive.

Do not expose the battery to moisture or rain.

Keep battery away from fire or other sources of extreme heat. Do not incinerate. Exposure of battery to extreme heat may result in an explosion.

General Battery Information

What Are The Different Types of Rechargeable Battery Chemistries / Technologies?

Batteries in portable consumer devices (laptops and notebooks, camcorders, cellular phones, etc.) Are principally made using either Nickel Cadmium (NiCad), Nickel Metal Hydride (NiMH) or Lithium Ion (Li-Ion) technologies. Each type of rechargeable battery technology has its own unique characteristics:

NiCad and NiMH:

The main difference between the two is the fact that NiMH batteries (the newer of the two technologies) offer higher energy densities than NiCads. In other words, pound for pound, NiMH delivers approximately twice the capacity of its NiCad counterpart. What this translates into . is increased run-time from the battery with no additional bulk to weigh down your portable device NiMH also offers another major advantage: NiCad batteries tend to suffer from what is called the “memory effect” NiMH batteries are less prone to develop this dreaded. affliction and thus require less maintenance and care. NiMH batteries are also more environmentally friendly than their NiCad counterparts since they do not contain heavy metals (which present serious landfill problems).

ACER 4ICR17/65 Laptop Battery

Li-Ion

Li-Ion has quickly become the emerging standard for portable power in consumer devices. Li-Ion batteries produce the same energy as NiMH batteries but weigh approximately 35% less. This is crucial in applications such as camcorders or notebook computers where the battery makes up a significant portion of the device’s weight. Another reason Li-Ion batteries have become so popular is that they do not suffer from the memory effect AT ALL. They are also environmentally friendly because they don’t contain toxic materials such as Cadmium or Mercury.

What is the “Memory Effect”?

NiCad batteries, and to a lesser extent NiMH batteries, suffer from what’s called the “memory effect”. What this means is that if a battery is repeatedly only partially discharged before recharging, the battery “forgets” that it has the capacity to further discharge all the way down To illustrate:. If you, on a regular basis, fully charge your battery and then use only 50% of its capacity before the next recharge, eventually the battery will become unaware of its extra 50% capacity which has remained unused . The battery will remain functional, but only at 50% of its original capacity. The way to avoid the dreaded “memory effect” is to fully cycle (fully charge and then fully discharge) the battery at least once every two to three weeks. Batteries can be discharged by unplugging the device’s AC adapter and letting the device run on the battery until it ceases to function. This will insure your battery remains healthy.

Is it Possible to Upgrade the Device’s Battery to a Newer Chemistry?

NiCad, NiMH and Li-Ion are all fundamentally different from one another and cannot be substituted unless the device has been pre-configured from the factory to accept more than one type of rechargeable battery technology. The difference between them stems from the fact that each type requires a different charging pattern to be properly recharged. Therefore, the portable device’s internal charger must be properly configured to handle a given type of rechargeable battery.

Refer to the owners manual to find out which rechargeable battery types the particular device supports or use our QuickFind search engine to find the device in our database. It will automatically list all of the battery types supported by the machine.

The New Battery Isn’t Charging. What’s the Deal?

New batteries are shipped in a discharged condition and must charged before use We generally recommend an overnight charge (approximately twelve hours) Refer to the user’s manual for charging instructions Rechargeable batteries should be cycled -… Fully charged and then fully discharged – two to four times initially to allow them to reach their full capacity (Note: it is normal for a battery to become warm to the touch during charging and discharging)..

New batteries are hard for the device to charge;.. They have never been fully charged and are therefore “unformed” Sometimes the device’s charger will stop charging a new battery before it is fully charged If this happens, remove the battery from the device and .. then reinsert it The charge cycle should begin again This may happen several times during the first battery charge Don’t worry;. it’s perfectly normal.

How Can I Maximize Battery Performance?

There are several steps you can take to insure that you get maximum performance from the battery:

Break In New Batteries

New batteries come in a discharged condition and must be fully charged before use. It is recommended that you fully charge and discharge the new battery two to four times to allow it to reach its maximum rated capacity.

Prevent the Memory Effect

Keep the battery healthy by fully charging and then fully discharging it at least once every two to three weeks. Exceptions to the rule are Li-Ion batteries which do not suffer from the memory effect.

Keep the Batteries Clean

It’s a good idea to clean dirty battery contacts with a cotton swab and alcohol. This helps maintain a good connection between the battery and the portable device.

Exercise the ACER 4ICR17/65 Replacement Battery

Do not leave the battery dormant for long periods of time. We recommend using the battery at least once every two to three weeks. If a battery has not been used for a long period of time, perform the new battery break in procedure described above.

Battery Storage

If you don’t plan on using the battery for a month or more, we recommend storing it in a clean, dry, cool place away from heat and metal objects NiCad, NiMH and Li-Ion batteries will self-discharge during storage; remember to break them in before use. Sealed Lead Acid (SLA) batteries must be kept at full charge during storage. This is usually achieved by using special trickle chargers. If you do not have a trickle charger, do not attempt to store SLA batteries for more than three months.

For Notebook Users

To get maximum performance from the ACER 4ICR17/65 Replacement Battery, fully optimize the notebooks power management features prior to use Power management is a trade off: better power conservation in exchange for lesser computer performance The power management system conserves battery power by setting the processor to run at. a slower speed, dimming the screen, spinning down the hard drive when it’s not in use and causing the machine to go into sleep mode when inactive. The notebook users guide will provide information relating to specific power management features.

ACER 4ICR17/65 Laptop Battery

How Are Batteries Rated? (What Are Volts and Amps?)

There are two ratings on every battery:. Volts and amp-hours (AH) The AH rating may also be given as milliamp-hours (mAH), which are one-thousandth of an amp-hour (for example, 1AH is 1000mAH) . The voltage of the new battery should always match the voltage of your original unless the batteries are different chemistries (NiMH and Li-Ion batteries have different voltage ratings, even if they’re for the same laptop). Some Hi-Capacity batteries will have higher amp-hour ratings than the original battery found in the device. This is indicative of a longer run-time (higher capacity) and will not cause any incompatibilities.

New Rating Watt-Hour (Wh):

Watt-Hour, or Wh, is a more accurate unit to show the power capacity than Amp-. Hour (Ah) that was used before. The Watt-Hour unit means the wattage that the battery can provide within one hour. 90 Watt-hour (Wh) capacity means the battery can theoretically last 90 hours if the device it powered only needs 1 Watt power, or 1 hour if the device need 90W power. A typical 6-cell internal notebook battery capacity is about 49 Watt-hour. A typical 12-cell internal notebook battery capacity is about 98 Watt-hour.

There are many different ways to rate a battery capacity on market. A lithium-ion battery cell capacity is usually measured in Ampere-hour (Ah). Since a battery pack battery uses many battery cells, some cells are connected in parallel, some are connected in serial, using Watt-hour will be more accurate to rate its capacity. If using Ampere-hour to rate its capacity, it should state the Ampere-hour capacity is under which given voltage. For example, 4000 mAh at 11.1V means the battery capacity is 4000 mAh x 11.1V = 44.4 Watt-hour (Wh). 4000 mAh at 14.8V means the battery capacity is 4000mAh x 14.8V = 59.2 Watt-hour (Wh). Although the two batteries have same Ampere-hour , their actual capacity is different.

How Long Do Batteries Last (What is the Life Span of the New ACER 4ICR17/65 Replacement Battery)?

The life of a rechargeable battery operating under normal conditions is generally around 500 charge-discharge cycles. This translates into one and a half to three years of battery life for the average user. The amount of charge a battery can hold gradually decreases due to usage and aging. When a battery that originally operated the notebook for two hours is only supplying the user with an hour’s worth of use, it’s time for a new one.

Battery Life Expectations:

Battery operating time is affected by:

Types of power conservation features activated on the computer

Computer’s type of display and microprocessor

Number and type of PC Cards and other devices used

Types of application programs running

Should I Recycle the Old Battery? How?

NiCad, NiMH and Li-Ion batteries should be recycled Be environmentally conscious -. Do NOT throw these batteries in the trash.

If you don’t know where your local recycling facility is, call the Portable Rechargeable Battery Association at 1-800-822-8837. They will provide you with the address of the recycling center nearest to you. Is it Possible to Upgrade the Device’s Battery to a Newer Chemistry?

NiCad, NiMH and Li-Ion are all fundamentally different technologies and cannot be substituted for one another unless the device has been pre-configured from the factory to accept more than one type of rechargeable battery. The difference between them stems from the fact that each technology requires a different charging pattern to be properly recharged. Therefore, the portable device’s charger must be properly configured to handle a given type of rechargeable battery.

Refer to the owners manual to find out which rechargeable battery types the particular device supports or use our QuickFind search engine to find the device in our database. The database will automatically list all of the battery types supported by the machine.

What is a “smart” ACER 4ICR17/65 Replacement Battery?

Smart batteries have internal circuit boards with smart chips which allow them to communicate with the notebook and monitor battery performance, output voltage and temperature. Smart batteries will generally run 15% longer due to their increased efficiency and also give the computer much more accurate “fuel gauge “capabilities to determine how much battery running time is left before the next recharge is required.

The New Battery Isn’t Charging. What’s the Deal?

New batteries are shipped in a discharged condition and must charged before use. We generally recommend an overnight charge (approximately twelve hours). Refer to the user’s manual for charging instructions. Rechargeable batteries should be cycled (fully charged and then fully discharged) two to four times initially to allow them to reach their full capacity (Note: it is normal for a battery to become warm to the touch during charging and discharging)..

 

New batteries are hard for the device to charge;.. They have never been fully charged and are therefore “unformed” Sometimes the device’s charger will stop charging a new battery before it is fully charged If this happens, remove the battery from the device and .. then reinsert it The charge cycle should begin again This may happen several times during the first battery charge Don’t worry;. it’s perfectly normal.

And now the disclaimer: Any statements and data in this file are for general information purposes They represent the latest technical status at the time of publishing BiX reserves the right to change the data in this file without prior notice The technical information is given… in a descriptive way and does not guarantee any properties or enlarge any warranties given.

Warranty Info: Battery warranty covers manufacturing and quality defects Please note that the amount of charge a battery can hold gradually decreases due to usage and aging How long your battery’s lifetime can last is depending on how you use it and how well you keep it!. and which is not a warranty issue.

How to Know When It’s Time to Replace Your Laptop’s Battery

No matter how well you treat your laptop’s battery, it will eventually die. If you’re lucky, it will be time to replace your laptop by the time its battery dies. If you’re not, you’ll need to replace the battery .

ACER W84066LC Replacement Battery  death can seem sudden, but it doesn’t have to. Windows will warn you when your battery reaches extremely low capacity levels, but you can also keep your own tabs on its capacity.

Windows Will Warn You

Windows doesn’t normally keep you up-to-date with your battery’s capacity level. As you use it and it weakens, you’ll just notice that your laptop doesn’t seem to last as long on battery.

Eventually, when your battery reaches a low enough capacity level, Windows will warn you. You’ll see a red X appear on the standard battery icon in your system tray and, when you click it, Windows will inform you that you should “consider replacing your battery “Windows also says that your computer might shut down suddenly because there’s a problem with your battery -. in other words, your battery can’t hold enough of a charge to power your laptop for long when it’s not connected to an outlet .

Note that this warning was added in Windows 7, so you won’t see it if you’re using Windows Vista or XP.

ACER W84066LC Laptop Battery

How to Check Your ACER W84066LC Replacement Battery  Capacity

Some batteries may display more information, such as the number of charge and discharge cycles they’ve been through.

Calibrating Your Battery

The information above may not be completely accurate if your battery requires calibration. For example, we had a battery that reported it was almost dead. Windows warned us that it was time to replace the battery and the battery appeared to be at 27.7% wear level according to its reported capacity.

After we calibrated the battery, Windows stopped warning us and the battery’s reported capacity went back up to 70.8%. The battery didn’t actually gain any additional charge, but the calibration helped the battery’s sensor actually detect how much capacity was in the battery. If Windows says it’s time to replace your battery, be sure to calibrate it first before checking its actual wear level. If you don’t, you may replace a battery that’s still in good enough shape. That would just be a waste of money.

Why Your Laptop’s Battery Capacity Declines

ACER W84066LC Replacement Battery decline due to a number of factors Heat, usage, age -. All of these things are bad for batteries Batteries will slowly die no matter what -. Even if you put your battery in a closet and never touched it, it would slowly lose capacity due to age However, if you never use your battery -. say you use your laptop at your desk most of the time and it gets rather hot, which is bad for the battery – removing the battery can certainly help prolong its life.

To make your laptop’s battery last longer, read our explanation of battery life myths and facts to know what works and what doesn’t.

Replacing Your Battery

If your laptop has a user-serviceable battery – that is, one you can remove on your own -. You can replace your battery fairly easily If your laptop doesn’t have a user-serviceable battery, you’ll need to contact the laptop’s manufacturer so they can crack your laptop open and change its battery for you.

There’s no point in obsessing over your battery’s capacity – it was designed to be used, after all -. But it’s something to keep on eye on If your capacity is dropping more quickly than you’d like, that may be a sign that you should be treating your battery better. Perhaps you’re exposing it to too much heat if you leave your battery in while playing demanding, strenuous PC games on your laptop.

How to Clean a CPU Fan

How to Clean a CPU Fan
Failing to clean your IBM 42X3805  CPU Fan can cause the fan to either slow down or to fail completely. If the fan fails, then the temperatures inside the CPU case will significantly increase, which creates the potential for overheating. The easiest way to clean a CPU fan is to use a can of compressed air 。

IBM 42X3805 CPU Fan

1.Shut down your PC and turn the power off. Remove the power cords from the rear of the tower and disconnect them from their power source.
2.Place the tower on top of an antistatic mat that has been laid on top of a table. You may also wear an antistatic wristband that is connected to an electrical ground, like a metal plumbing fixture. You’ll need to use the antistatic devices because static discharge from the floor or from your body could damage data stored on the computer.
3.Open the back of the computer case according to the directions in your owner’s manual. Some IBM 42X3805  CPU Fan will require screwdrivers for removal, while others will have buttons to depress before the back comes off.

4.Position your can of compressed air at least two inches from the surface that you are cleaning.

5.Clean the fan intakes and the exhaust using short puffs of canned air. The intakes are the grid-like structures that filter the air that comes into the fan.
6.Spray short puffs of canned air over the fan blades. To loosen clumps of dirt, hold your canned air at multiple angles rather than using long bursts of air. Make sure that you do not touch anything inside of the CPU tower.
7.Set the canned air aside and close the back of your CPU.
8.Clean the exterior of your CPU with a damp cloth that has been dipped in soapy, lukewarm water. Dry the surface with a soft towel.
9.Use a damp cloth to clean your power cords while they are disconnected from a power source. Dry the power cords with a soft towel.
10.Return the power cords to their correct positions and power up your computer.
Tips
1.While you are cleaning the IBM 42X3805 CPU Fan, clean the motherboard and other areas if needed, utilizing short bursts of canned air.

2.Minimize airborne dust in your computer room by cleaning the room regularly. You may also cover your equipment in order to keep dust out.
Warnings: If your CPU fan is not working, then you should only run your computer for a few minutes at a time to avoid overheating and damaging your stored data.

How to change a cpu fan

Upgrading your standard IBM 13N5182 CPU Fan has numerous benefits. It can extend the life of your CPU, moderate temperatures of a CPU that endures less than ideal thermal environments, give you more head room when over clocking, and give your case a little more visual appeal. Great for those that have a case featuring a clear side window. There seems to be an endless selection of aftermarket IBM 13N5182 CPU Fan to choose from, and your decision should be based on how much physical clearance you have (motherboard and case), motherboard socket type , your budget and what you want from the cooler (high performance, looks or a combination of both). The process of changing a CPU cooler can be a little daunting for some and if not done carefully can go wrong. The intention of this guide is to give beginners an insight into what’s involved when changing a CPU cooler;. in most cases the manufacturer will provide you will detailed instructions on how to install their product Think of this as a little preview before you dive right into it, and if you have any questions please feel free to ask on our forums.

IBM 13N5182 CPU Fan
Before the motherboard can be removed everything connected to it, excluding the RAM modules and actual CPU, has to be removed or unplugged. So your graphics card / s, PCI devices have to removed, SATA / IDE cables, audio cables, USB cables, motherboard power cables, front panel button and lights cables and any 3 pin case fans that are connected. This can be the scary part for anyone that has never attempted this before but if you take note of what goes where you should be fine. If you are unfamiliar with what cables with this make sure you have your motherboard and case manual with you for when you reinstall everything, then it will be just a case of matching everything back up. With the motherboard screws removed you can lift the motherboard out of the case and now you have full access to both sides of the motherboard.
For this particular motherboard there is four screws holding the front bracket to the standard backing plate. Remove the four screws and put all the standard retaining hardware aside.
Here’s the motherboard free from all standard IBM 13N5182 CPU Fan hardware. Before installing the new aftermarket CPU cooler you have to clean the surface of the CPU. To remove the old thermal compound uses a lint free cloth and some rubbing alcohol. Be careful not to smother the CPU in rubbing alcohol you’ll only need a small amount on the cloth.
Here’s the back of the motherboard ready to have the aftermarket backing plate fitted. Some coolers will come with double sided tape to hold the backing plate in place and some don’t.
Now it’s time to fit the retention bracket that comes with the aftermarket cooler, most of these coolers will come with a number of brackets to suit multiple socket types. Use the provided manual to ensure that you select the correct bracket for your socket type. As you can see in the above picture I have already fitted the brackets to suit the AMD socket.
The screws hold down the retention brackets and come through the motherboard then get fastened to the pre-threaded backing plate. (Each aftermarket cooler will have a different retention bracket setup) Before you get too excited and apply the thermal compound try test fitting the aftermarket cooler first to make sure you have the brackets in the right orientation.
Apply a thin layer of thermal compound to the CPU surface. Some aftermarket coolers will come with thermal compound that features an application brush, some will come in a squeeze tube and some just in a sachet. If you get the later two then just apply a small amount of thermal compound in the center of the CPU (approximately the size on a grain of rice) and spread the paste evenly across the CPU surface. Use a business card to spread out the thermal compound evenly across the CPU surface until you have a semi transparent layer.
The IBM 13N5182 CPU Fan will come with a protective sticker / cover over the heat sink contact area that you will have to remove prior to fitting. After that place the CPU cooler onto the retention bracket and fasten it down using the provided screws / bolts / thumb screws , ensure that you tighten each screw down evenly and don’t over tighten it or you may damage the mother board. Now it’s just a case of reversing the disassembly process you went through to remove the motherboard. Take your time here especially now that you have a larger CPU cooler in the way.

How to replace a broken laptop screen

A cracked screen can make a laptop unusable. Luckily, you can fix it. I will give you step-by-step instructions for replacing a broken laptop LCD panel.

Whether it’s cracked or has one too many blown pixels, a broken laptop display can stop you dead in your tracks. But with the right tools, a little technical know-how, and a bit of patience you can replace a damaged LCD.

Note: In this article, I show you how to replace the screen on an Dell JJ451 laptop screen, which has an LED-backlit LCD Depending on the make and model of your laptop, the internal hardware and specific steps may vary The general.. process however, should be the same.

Should you try this fix?

If accidental damage is covered under your laptop’s warranty, don’t do this fix yourself. Get the laptop repaired under the warranty.

I also suggest you watch my earlier video on what to know before trying to fix a smartphone or tablet. It’s not specifically about laptops, but the information is still relevant, and it will help you decided if you should repair the machine yourself or take it to a shop.

Lastly, understand that if you follow the instructions in this video, you do so at your own risk. Neither CNET nor any of its representatives can be held responsible for injury, damage, or loss of data.

Getting a replacement screen and tools

To begin your fix, you’ll need a few simple tools and a replacement LCD screen. For tools, I recommend a screwdriver with a variety of small bits, These are really handy for removing the trim that surrounds the screen.

As for the replacement LCD, you should be able to buy one either from the laptop manufacturer’s authorized parts dealer or a third-party supplier Depending the screen, they usually cost between $ 50 and $ 250 dollars -. More if it’s a high-end display or you buy an OEM replacement. Regardless, you’ll want to buy a new screen that matches your broken one exactly. The only sure way to do this is to remove the broken one.

Dell JJ451 Laptop Screen

1. Remove the screen bezel

After disconnecting the power supply and removing the battery, carefully examine the bezel around the screen. You’ll need to remove this bezel to access the screws that hold the LCD panel in place.

On this laptop, several rubber cushions hide screws, which hold the bezel in place. I’ll need to remove these cushions and the screws that are underneath.

With the hidden screws removed, I used a thin metal blade to pop loose one of the bottom corners and worked my way around the bezel with a plastic spudger.

Note: Your laptop may not have cushions or hidden screws The bezel may simply snap onto the lid or be held in place with double-side tape Just, adapt my instructions to fit your specific laptop…

Regardless of how you do it, you’ll need to completely remove the bezel.

2. Remove the broken Dell JJ451 Laptop Screen

With the LCD’s mounting brackets exposed, you can remove the screws that secure it to the lid. Then rest the display front-side-down on the case and disconnect its cable.

If your laptop was made before 2010 and has a LCD with fluorescent backlights, it will likely have two cables. But as this is an LED-backlit LCD, it only has one.

Now, locate the manufacturer’s label and note the model number. Using this information you should be able to buy an exact match for your broken screen.

3. Install the new Dell JJ451  Laptop Screen

Once your new screen arrives, unpack it and make sure it matches the old one.

If the dimensions, mounting brackets, and connector all match, you ready to install the screen. Connect the new panel to the cable, position the panel in the lid, and secure it using the appropriate screws.

4. Test the new LCD panel and reinstall the bezel

Before reattaching the bezel, it’s a good idea to test the new panel. Reconnect the battery and power cable and turn the machine on. If the display works, you can reattach the bezel and any external screws and rubber cushions. The repair is now complete .

As fixes go, this one isn’t too tough, but it does take a little patience and planning to make sure you get the right replacement screen.

How to Raise LENOVO G560 CPU Fan Speeds on a Lenovo Laptop

If your business requires you to do a lot of work from your Lenovo laptop, you’ve probably noticed an occasional issue with overheating. Running several intensive programs on your laptop can raise the CPU temperature, causing the LENOVO G560 CPU Fan to engage. You may need to raise the speed of the fans from time to time to rapidly cool the CPU and prevent a sudden shutdown. You can boost CPU fan speed from your laptop’s BIOS menu.

Step 1

Install the latest BIOS update on your laptop if necessary. This update can be downloaded free from the Lenovo Support page (link in Resources).

Step 2

Turn off your computer after you’ve installed the update. Turn the computer back on. When the boot screen appears, press and hold the “Delete” key to load the BIOS settings menu.

Step 3

Press the directional arrows on your keyboard to select “System Monitor.” Press “Enter.” Select “Fan Control” and then select “CPU Fan Speed Control.”

Step 4

Switch the control from “Automatic” to “Manual.” This allows you to manually control the CPU fan speed by percentage.

Step 5

Enter the desired percentage at which the fan should run. To run at full speed, enter “100″ for 100 percent. You should only run fans at full speed for long enough to effectively cool the CPU.

Step 6

Press the “F10″ key to reboot the computer and raise the speed of your CPU cooling fans. To return the fan speed to normal, repeat the above procedure but switch the LENOVO G560 CPU Fan control back to the “Automatic” setting.

Can You Clean the Contact Between a CPU & Fan?

Step 1

Unplug the ASUS CPU Fan power cord from the motherboard and unscrew or unlock the connectors holding it down — there is usually one in each corner. Pull it straight out of your computer case.

Step 2

Release the lever holding your CPU down, and then push the metal strips that were holding it down all the way back. Grip two corners of the CPU with two fingers, and then lift it straight out of the computer case.

Step 3

Set the CPU and CPU fan contact sides up on a clean paper towel. Dampen another paper towel or coffee filter with isopropyl alcohol, and then carefully wipe the thermal paste off the contact areas of your CPU and CPU fan. If necessary, dampen a cotton swab with the isopropyl alcohol to clean it out of any crevices it got into. When done, wait a moment for the CPU and CPU fan to dry completely.

Step 4

Put the CPU in the desired computer’s CPU slot, and then lock it into place with the lever on the motherboard. Squeeze a small amount — a bit smaller than pea-sized — of new thermal paste onto the center of the CPU’s metal plate.

Step 5

Position your CPU fan over the CPU, and then line up its four connectors with the four connections on the motherboard. Push it into place, and then lock the connectors in to secure it. The new thermal paste will spread to cover the contact areas on the CPU and ASUS CPU Fan. They are now ready for use.

How to Test a APPLE CPU Fan

Testing an Installed Fan

Step 1

Download and install SpeedFan. This program uses data provided by sensors in your computer’s hardware to display information about the temperatures of various components and the speed at which the APPLE CPU Fan for those components are rotating.

Step 2

Launch SpeedFan and wait a few minutes for it to retrieve data.

Step 3

Examine the information presented in the main program window. The speed at which your computer’s fans are rotating, measured in revolutions per minute, is on the left side of the window, while temperatures of various components are on the right side. The RPM data for the CPU fan is listed first, but may be labeled differently depending on the data sent by your hardware.

Step 4

Check the RPM data for your CPU fan and compare it with the normal RPM range listed in the manual or specifications sheet for it. A particularly low RPM number may indicate your fan is failing.

Step 5

Click the “Charts” tab, select “Fan Speeds” using the drop-down menu and place a check mark next to the label corresponding to your CPU fan to begin generating a chart of the variation in the fan’s speed. Leave the program running for some time while you use your computer. Later, check the chart; a significant variation in the RPM number, in the order of 1000 to 2000, may also indicate a failing fan.

Testing a Fan Separately

Step 1

Remove the power supply from your computer, disconnecting all cables. If you have access to a spare working power supply, using that one instead will save you the time spent disconnecting it and reconnecting it.

Step 2

Check the power supply for a three-pin fan connector. Many modern power supplies have this connector; if your power supply lacks it, you will need to purchase a four-pin Molex to four-pin Molex plus three-pin fan splitter cable.

Step 3

Bend or cut a metal paper clip to create a “U” shape.

Step 4

Identify the 24-pin main power connector and locate a green wire and a black wire.

Step 5

Insert one end of the U-shaped paper clip into the pin corresponding to the green wire and the other into the pin corresponding to the black wire.

Step 6

Connect the fan you want to test to the power supply using the three-pin fan connector and, if necessary, the splitter cable.

Step 7

Plug the power supply into an electric socket using the appropriate power cable and, if necessary, turn it on using the switch on the back of it. Check whether APPLE CPU Fan on the power supply is spinning to ensure it is on.

Step 8

Check if the fan you are testing is spinning, if it’s making any odd noises, stuttering or abruptly changing speeds.